The washing machine has been on the market for decades, but there are still a lot of people who don’t know much about how to get their washing machine working again. If you have a broken washer, you’ll need to use some basic home repair techniques and tools. You can buy a replacement part online or at your local hardware store, but before you do that, be sure to check out our tips below.
Step 1: Check Your Washing Machine’s Drain Pipes
If your washing machine is leaking water from its drain pipe, you should start by checking if everything looks okay with the drain. After all, this is where most of the water will go. First, turn off the power supply to the appliance, then remove the front panel. Next, take off the top cover and look inside. If the rubber gasket around the drain isn’t cracked or otherwise damaged, then it should work fine. But if you see signs of wear, such as cracks in the rubber gasket that could leak water, you may want to replace the gasket.
If you find any other problems, you might also consider replacing the entire drain assembly. You’ll find many parts available online that will fit your specific model. The part number for the drain assembly might be printed on one side of the plastic housing, so you’ll definitely want to keep an eye out for it once you locate the drain. Once you’ve replaced the whole assembly, make sure that everything fits properly. Also, test your new gasket by turning the machine on and watching for any leaks. If it works well, you’re done. If not, you may have to repeat the process until you find the right gasket.
The first thing that a person can check is the Washing machine drainage options. There are varieties of the drainage option that are available with the advancement in technology. If the person will have the idea of the various options then reaching the goals will become easy. The main motive of the people is to get the results in the best possible way. A person can work in a better way for the guidance of the people.
Step 2: Clean out Your Washer Drain Pipe
Next, you’ll need to clean out the drain pipe. If you live in a cold climate, you may want to leave on your clothes during this step. This way, the warm air surrounding them will help melt any ice or snow that may have accumulated in the pipe. Otherwise, you can use a hose and/or a shop vacuum cleaner (such as a Hoover) to clear the debris. If the drain pipe is blocked, you might need to add more soap and hot water through the drain valve. Then turn the machine back on and let it run for several minutes.
Afterward, rinse out the washer drain pipe with a garden hose. If you have any remaining dirt or grease, wipe it away with a damp cloth. Now you can put everything back together and turn the power supply back on.
Step 3: Reinstall Your Washer Drain Pipe
It’s time to reassemble your washer drain pipe. You’ll probably find instructions somewhere on your owner’s manual, but you can always ask for help from your neighbor or family member. Just make sure they understand which direction the pipes should face so that you can insert them into place.
When you’re finished, be sure to tighten every screw down tightly so that the pipes stay put. You’ll also want to make sure that everything lines up correctly. For instance, if you have a washer drain pipe that extends more than 6 inches vertically, you’ll need to install a flexible elbow in order to accommodate it. This is because the pipe will be too long to fit through the hole in the wall.
Step 4: Check Your Washing Machine’s Water Level
If you notice that your washing machine won’t fill up with water, it may be because the level indicator is stuck. To fix this problem, you’ll first need to open up the cabinet and reach inside. There should be a little plastic tube that runs along the bottom of the drum. This is called the float arm. Remove your fingers from the opening and gently push the float arm downward. When you see it stop moving, you can pull it upward. Make sure that it moves freely back and forth. If it doesn’t move freely, you’ll need to change out the float arm.
Once you’ve cleared the float arm, you should be able to see a white water gauge with a small black pointer inside of it. This indicates the current water level. If the pointer is sitting near the top of the scale, then you’ll need to lower the water level. Conversely, if the pointer is sitting near the bottom of the scale, you’ll need to raise the water level. It may help to place something under the washer so that you can lift it easily.
Step 5: Test Your Washing Machine
Now it’s time to test out your washing machine. Turn the power supply back on, and after the machine warms up, press down on the spin cycle button. As you watch, you’ll see the water begin to fill up. Give the machine a minute or two, and then you should hear the water filling up even further. Keep going until the wash cycle ends and the final water level is reached. You can now turn off the power supply, and you’re done!
If you encounter any other problems, you should consider calling a professional service technician. They can inspect your washer drain pipe, clean the debris out of the drain, and get the washer drain pipe flowing again.